Sanding and refinishing old parquet

Sanding and refinishing an old parquet floor is priced on a visit, because it depends on the floor's condition. Solid parquet can be sanded many times. Engineered with a wear layer of 4 mm or more can be refinished at least twice.

What decides the price, how a floor is sanded and how many times it can be done.

Free and no obligation. Your request goes to one fitter in your county, not a list.

  • many timessolid parquet can be sanded
  • at least twiceengineered with a 4 mm wear layer
  • 2 coatsof hardwax oil after sanding
  • a dayfor the glue to cure before sanding new blocks
A chair holding a blowtorch and gloves on an oak parquet floor with a herringbone centre and a border

What decides the price

Nobody publishes a flat rate for sanding old parquet, because every floor starts in a different state. The fitter looks at four things.

  • Loose or missing blocks. They are re-glued or replaced before any sanding. This is where parquet costs more than a plank floor.
  • Old finish. Layers of varnish or wax take longer to take off.
  • The area. A larger floor is cheaper a m², and a very small one carries a minimum.
  • The new finish. Hardwax oil or lacquer, and how many coats.

Price your herringbone floor

Three taps and the price shows as you go. Your name and number come last, and only if you want a fitter to price it.

Restoring an old parquet floor, 20 to 40 m², supplied and fitted: Priced on a visit.

Step 1 of 5

What floor are you after?

Pick the closest. The fitter asks the rest.

How the price is worked out

The figure is what Irish sellers and fitters charge a square metre, times the area you pick. Engineered wood is the supplied-and-fitted range. Laminate and vinyl add fitting at plank rates, so herringbone adds to them. Tile is the tile only. Where nobody publishes a figure, it reads priced on a visit. Use it to plan with. It isn't a quote: a fitter prices yours after seeing the floor.

How a floor is sanded

The work goes through progressively finer grits and ends with a fine orbital sand. Then the finish goes on: two coats of hardwax oil, the first soaking in and drying and the second building the surface. The floor is ready for normal use a day or two after the last coat.

How many times it can be done

Solid parquet

Sanding
Many times
With a 4 mm wear layer
Not applicable
Lasts
Generations of sanding

Engineered parquet

Sanding
Once or twice, set by the wear layer
With a 4 mm wear layer
At least twice
Lasts
30 to 50 years with a 4 mm layer

Ask for the wear layer in millimetres if the floor is engineered. A thin one limits how much can come off.

Sand it or replace it

Where a floor is sound but tired, sanding and oil bring it back for a fraction of what a new floor costs. Where blocks are rotten, lifted by damp or badly cupped, replacing the floor is the better call. A supplied-and-fitted oak herringbone floor is €95 to €130 a m² for engineered and €110 to €160 a m² for solid. The price guide.

Questions before you buy

How much does it cost to sand a parquet floor?

It is priced on a visit. The fitter looks at loose blocks, the old finish and the area first.

How many times can I sand a herringbone floor?

Solid parquet many times. Engineered with a 4 mm wear layer or more, at least twice.

How long does a floor take to dry after oiling?

Normal use starts a day or two after the last coat.

Can I sand engineered herringbone?

Once or twice, depending on the wear layer.

Do loose blocks cost extra?

Yes. Loose or missing blocks are re-glued or replaced before sanding, and that adds to the price.

Everything on this site

A large bright room with a light herringbone oak floor and arched alcoves

See the price before anyone rings

Pick the floor, how big it is and where you live. When you want a firm price, it goes to a single floor fitter in your county.